the attention on Electrician's knife

Discussion on Motor Market

New marketing model of hardware industry

Auto repair tools under the new revolution

Changes and transformations in the new situation

Development and opportunities of new energy motor hub

Whether to add lubricating oil to automobile tire bearings

How to judge whether the shock absorber spring is damaged

What is the difference between a car's air brake and an oil brake

Main points of car brake system maintenance

What is the performance of a broken car wheel bearing

The 22nd China International Industry Fair

The importance of bearings in automobiles

New materials and new technologies and new formats

Central China Hardware Show-Zhengzhou Station

New layout in the field of lithium batteries

Removing the steering wheel from your car or truck is not a difficult task if you have the right tools, particularly a steering wheel puller. But if you don't have a steering wheel puller, taking off the steering wheel becomes a bit trickier. You have to be a bit more creative than you would be under normal circumstances and employ a few nontraditional methods, but it can still be done at home with a few more common tools.

If you're not experienced with vehicles, you may not realize there are two different types of brake calipers. One is floating and the other is fixed. Even though they don’t need maintenance, their failure is common. These guidelines will help you figure out how to change brake calipers.

Most brake calipers do not need to be rebuilt or replaced the first time the brakes are relined. But after 75,000 miles, or seven to 10 years of service, the calipers may be reaching the end of the road. As the rubber seals age and harden, the risk of sticking and leaking goes up.

The oil filter gets contaminants out of engine oil so the oil can keep the engine clean, according to Mobil. Contaminants in unfiltered oil can develop into hard particles that damage surfaces inside the engine, such as machined components and bearing surfaces.

There are different applications of coil spring suspension. On most front-wheel-drive cars, coil springs are assembled to the strut, coiling around it. Heavier-duty vehicles place coils between the chassis and the frame and feature shocks as a separate suspension component.

The air-conditioning system in your Ford is basically a circulation loop through which refrigerant is pumped by a compressor. The refrigerant is a combination of gas and liquid that becomes very cold as it is compressed and then expanded. The chilled gas then flows from the compressor into an evaporator coil. The cold refrigerant now inside the coil has air blowing across the fins and tubes of the coil, thereby cooling the air, which is transferred into the car.

Most modern cars have brakes on all four wheels, operated by a hydraulic system . The brakes may be disc type or drum type.The front brakes play a greater part in stopping the car than the rear ones, because braking throws the car weight forward on to the front wheels.Many cars therefore have disc brakes , which are generally more efficient, at the front and drum brakes at the rear.

The SRT is the top-of-the-line Dodge Challenger. The rules for changing the oil are the same as they are for every vehicle. You should change the oil in your Challenger every 3,000 miles to keep it from breaking down and causing the engine to run without lubrication. It's also important to change the oil filter, as the old filter is contaminated and needs to be removed so it does not contaminate the new oil.

The engine is the heart of your car. It is a complex machine built to convert heat from burning gas into the force that turns the road wheels.

Ask any high-performance engine builder what the main cause of engine failure is and, short of parts breakage, it is problems with the oil supply. Oil is the life blood of an engine, and every moving component inside the engine is designed to operate on a cushion of oil. The faster you go--and, thus, the faster you turn the engine--the more oil pressure you need to provide the same level of lubrication as at the lower revolutions per minute.

A wheel bearing is a group of ball bearings that enables a wheel to spin freely. The bearing fits snugly inside the hub of each wheel, and while it can withstand a lot of abuse, heat and water can cause severe damage.

A Suburban's radiator is responsible for storing and cooling the antifreeze which flows throughout the engine. With the passage of time, a radiator's internal components begin to corrode, most commonly from rust. When this occurs, the radiator's ability to cool the antifreeze is significantly impaired. Where damage is not significant, a radiator can often be repaired, but in extreme cases the radiator must be replaced.

An automobile radiator is a metal device that is used to cool hot coolant that has flowed from the engine. Radiators are made to handle the stresses of heating and cooling, but can crack for various reasons.

Quick exhaust valves are used on certain mechanical parts to speed the reaction time of each part.

From vehicles to industrial tools, there are many products that use pneumatic systems. This means the system takes compressed air and uses it to control energy as it moves through the system. However, without pneumatic valves, these products don't work the way they're supposed to.

Electric hydraulic torque wrench hydraulic pump fluids are actually gear pumps, vane pumps, etc. Today, I will introduce to you electric hydraulic torque wrenches. Gear pumps are actually very common failures, and there will be wear between the pump body and gears. , The pump body and cracks are damaged, and the above conditions must be repaired. The following editor will discuss with you how to deal with the abnormal phenomenon of the hydraulic pump.

As a manufacturer and seller of automobile maintenance tools, dealing with auto repair tools is essential. Here are 7 special tools for car maintenance.

Last week we introduced several commonly used auto repair tools, today we will continue to talk about other auto special tools.

The hydraulic wrench is one of the commonly used hydraulic torque wrench kits, as well as the hydraulic torque wrench body and the special pump station for hydraulic torque wrenches. Hydraulic wrenches can be divided into drive type and hollow type, and there are three sources of pollution, external, internal and the system itself. Let's talk about them separately below.

How to Replace the Ball Joint of an Ford Cars

In General,Minor body damage occurs all the time. Door dings, bumper scrapes, scratches — these are all things that you may have a shot at repairing yourself.car body dent hammer set is designed to handle most metal fabrication and body repair jobs. Use the hammers and dollies to remove dings and dents, flatten metal panels, create outside curves and shrink metal

Analysis of the market status and development prospects of China's automotive aftermarket industry in 2020, China has a lot of room for development

Solution to extactor and change brake fliud oil(tip: replace brake oil)